Gefen 4x CAT6 Extender for HDMI Bedienungsanleitung

®44444444444444444444444444444444444xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxCAT6 Extenderfor HDMI®EXT-HDMI1.3-CAT6-4XUser Manualwwwwwwwwwwwwwwwwwwwwwwwwwwww

6RECEIVER PANEL LAYOUTFront PanelBack Panel13425678910

7RECEIVER PANEL DESCRIPTIONS1Control ButtonsWhen connected to any 4x4 Matrix for HDMI, these remote buttons on theReceiver unit can switch between the

8IR REMOTE DESCRIPTION1 Activity IndicatorThis LED will be activated momentarily each time a button is pressed.2 Input Source Selection Buttons (1 -

9RMT-4-IR REMOTE INSTALLATIONInstalling the RMT-4-IR BatteryTo use the RMT-4-IR Remote, remove the battery cover on the back of the remote to reveal t

10RMT-4-IR REMOTE CONFIGURATIONSetting the IR Remote Channel on the RMT-4-IRIn the event that IR commands from other remote controls confl ict with the

11CONNECTING THE 4X CAT6 EXTENDER FOR HDMIHow to Connect the 4x CAT6 Extender for HDMI(Matrix Mode)1. Using any 4x4 Matrix for HDMI as a source, conne

12How to Operate the 4x CAT6 Extender for HDMI(using an 4x4 Matrix)The front panel of each Receiver unit for the 4x CAT6 Extender for HDMI contains a

13How to Connect the 4x CAT6 Extender for HDMI with RS-232 control tothe 4x4 Matrix for HDMI and to the controlled device1. Follow steps 1 - 6 on How

1414How to Connect the 4x CAT6 Extender for HDMI(Stand-alone Mode)The 4x CAT6 Extender for HDMI is dependent upon an external 4x4 Matrix to manage all

15CONNECTING AND OPERATING THE4X CAT6 EXTENDER FOR HDMIRouting Sources using the Optional RMT-4-IR Remote Unit(Matrix Mode)There are a total of 4 butt

16How to Operate the 4x CAT6 Extender for HDMI(Stand-alone Mode)When the 4x CAT6 Extender for HDMI is used without an 4x4 Matrix, it can only be used

17CONNECTING AND OPERATING THE4X CAT6 EXTENDER FOR HDMIHow to Equalize the 4x CAT6 Extender for HDMI(Matrix Mode / Stand-alone Mode)The 4x CAT6 Extend

18DIP SWITCH CONFIGURATIONNOTE: By default, all DIP switches are set to the OFFposition.Default settings for DIP switchesDIP SwitchPosition1OFF2OFF3OF

19DIP SWITCH CONFIGURATIONDIP Switches(Matrix Mode / Stand-alone Mode)DIP 1 - EDID Management• OFF - Local EDIDWhen Local EDID mode is used, the EDID

20543219876123456789Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interfaceRS-232 SettingsBits per second ...

21RS-232 SERIAL CONTROL INTERFACERouting Sources using RS-232 Receiver Unit(Matrix Mode)1.Prepare the Receiver unit by connecting an RS-232 cable from

22Functions SyntaxyThe syntax for each function is always the same:#Character as the start fl ag → Function name → Space ( _ ) as function name end fl a

23M CommandThe M command displays the current routing status of the matrix.Syntaxy:mParameters:NoneFiber Optic Extender Status F0 CommandThe F0 comman

24RS-232 SERIAL COMMANDSGeneral FunctionsSimplifi ed syntax was used for command implementation for faster operation withthe device: # character – isn’

25IP CONTROLThe Gefen 4x CAT6 Extender for HDMI supports IP-based control using an integrated Web interface. To access this feature, an IP address, su

ASKING FOR ASSISTANCERev C4Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM

26IP CONTROLIP CONFIGURATIONTheIP CONFIGURATION page is used to set the IP settings that will be used toaccess the Web interface. The following items

27IP CONTROLBACKUP / RESTOREThe Backup/Restore page is used to backup and restore complete setup confi gurations.Note: This feature will be implemente

28IP CONTROLPOWER MANAGEMENTThePOWER MANAGEMENTpage is used to set optional +5V power on an input to power specifi c optional devices. The current stat

29NETWORK CABLE WIRING DIAGRAMGefen recommends the TIA/EIA-568-B wiring option. Please adhere to the table below when fi eld-terminating the CAT-6 cab

FIRMWARE UPDATE30Firmware Update ProcedureTo begin the update procedure, the unit’s Boot Loader must be activated. To activate the Boot Loader, follow

31FIRMWARE UPDATE11. Connect the RS-232 cable to the Receiver unit.12.Repeat steps 4 - 7 and upload RHDMIDCAT6x4_e_x_x.bin.13.Repeat step 11 - 13 for

32Video Amplifi er Bandwidth ... 225 MHzInput Video Signal...

33WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects

34LICENSINGlwIP is licenced under the BSD licence:Copyright (c) 2001-2004 Swedish Institute of Computer Science.All rights reserved.Redistribution and

CONTENTS1 Introduction2Operation Notes3Features4Sender Unit Layout5Sender Unit Description6Receiver Unit Layout7Receiver Unit Descriptions8 IR Remote

Rev C420600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefen.com [email protected] product uses

1INTRODUCTIONCongratulations on your purchase of the 4x CAT6 Extender for HDMI. Your complete satisfaction is very important to us.GefenGefen delivers

2OPERATION NOTESREAD THESE NOTES BEFORE INSTALLING OROPERATING THE 4X CAT6 EXTENDER FOR HDMI•CAT-6a cables can be used up to 200 feet (60 meters).•Shi

3FEATURESSupported HDMI 1.3 Features• 225 MHz (up to 12 bit YUV 444 @ 1080p)• Deep Color• Dolby TrueHD and DTS-HD Master Audio• Lip-Sync• CEC Pass-Thr

4SENDER PANEL LAYOUTFront PanelBack Panel12345678910

5SENDER PANEL DESCRIPTIONS1Standby ButtonSets the 4x CAT6 Extender for HDMI into Standby Mode.2 IR SensorReceives signals from the IR Remote Control.3