Gefen GTV-ETH-2COAX Bedienungsanleitung

www.gefentv.comEthernet Over CoaxGTV-ETH-2-COAXUser Manual

7RECEIVER PANEL DESCRIPTIONS1. Standby ButtonPressing this will put the receiving unit in standby mode. The unit will nottransfer any information to t

8How to Connect the GefenTV Ethernet Over CoaxInstallation of the GefenTV Confi guration Assistantg1. Download the latest software from the Support sec

9ETHERNET OVER COAX SOFTWARE INSTALLATION5. Make sure all other applications are closed, then press the Next button tocontinue.6. Please read the lic

107. Please choose the program installation destination. The default locationis “C:\ Program Files\Gefen TV Ethernet Over Coax”. To set your own desti

111. Connect the source (i.e. computer, router, switch) to the GefenTV EthernetOver Coax sender unit using the supplied CAT-5e cable.2.Connect the Gef

12CONFIGURING THE ETHERNET OVER COAXOnce both the sending and receiving units are linked and powered, basic confi guration can proceed. This section of

13CONFIGURING THE ETHERNET OVER COAX6. Once all possible nodes have been detected, the program will display all of these nodes as in the window below.

14CONFIGURING THE ETHERNET OVER COAX8.The PLC node confi guration screen is separated into the following items:NET IDThis is the name of the network. T

15CONFIGURING THE ETHERNET OVER COAX9. Once the update is complete, a message will appear to indicate the updatewas successful. Click on the ok button

16CONFIGURING THE ETHERNET OVER COAX11. Once the confi guration for the remote node is complete, the local node will then have to be confi gured. Click

ASKING FOR ASSISTANCETechnical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM Monday

17AUTOMATIC SECURITY CONFIGURATION FEATURETo quickly setup the Gefen TV Ethernet Over Coaxial for secure use, the Automatic Security Confi guration Mod

18AUTOMATIC SECURITY CONFIGURATION1.Connect the computer with the installed Gefen TV software to the node you wish to set as the Master node. 2. Press

19ADVANCED CONFIGURATIONThere are optional advanced settings that can be confi gured for each node. Theadvanced menu can be accessed directly through t

20ADVANCED CONFIGURATIONFirmware UpdateThis section is used to update the node’s fi rmware from a server location. Pleasesee the Firmware Update sectio

21ADVANCED CONFIGURATIONMULTICASTIGMP MulticastThis option will enable or disable the node’s ability to transmit IGMP multicastdata.SECURITYThe securi

22ADVANCED CONFIGURATIONVLANThis option will enable or disable the node’s ability to accept VLAN data. If this feature is enabled on one of the nodes,

23ADVANCED CONFIGURATIONADAVANCED QOSQQOS (quality of service) prioritization. Rule 1 will be applied to all packets fi rst and then Rule 2. Prioritiza

24WEB CONFIGURATIONIf an IP address has been set in the ADVANCE CONFIGURATION PANEL, access to the WEB UTILITYwill be enabled. To access the YWEB UTIL

25WEB CONFIGURATIONMAIN PAGEThe main page will display general confi guration information. Clicking on the further information link will navigate to a

26WEB CONFIGURATIONThe confi guration options are as follows:MAC Confi gurationNetwork Confi gurationMulticast Confi gurationVLAN Confi gurationPriority Co

CONTENTS1 Introduction2 Operation Notes3 Features4 Sender Panel Layout5 Sender Panel Descriptions6 Receiver Panel Layout7 Receiver Panel Description

27FIRMWARE UPDATE PROCEDUREThe fi rmware for the GefenTV Ethernet Over Coax can be updated by FTP,TFTP, or a direct fi le. The fi rmware update can be ex

28Standard Support ... UPA DHS (200 Mbps) PLCInterface ... One Power Line port / One coaxial

29WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects

Rev A420600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefentv.com [email protected] product u

1Congratulations on your purchase of the GefenTV Ethernet Over Coax. Your complete satisfaction is very important to us.Gefen TVGefen TV is a unique p

READ THESE NOTES BEFORE INSTALLING OROPERATING THE GEFENTV ETHERNET OVER COAX• This device passes all 10/100BASE-T Ethernet network protocols (TCP/IP,

3Features• Supports up to 200 Mbps data transmission rate• Extension of up to 1000 feet (300 meters)• Web confi guration for easy maintenance• Feature

4Front PanelBkP lTP lBack Panel14253Top Panelp678SENDER PANEL LAYOUT

5SENDER PANEL DESCRIPTIONS1. Standby ButtonPressing this will put the sending unit in standby mode. The unit will not transfer any information to the

6Front PanelBack PanelTP l14253Top Panelp67891011RECEIVER PANEL LAYOUT