Gefen 4x4 Matrix for HDMI with FST and 3DTV Spezifikationen

Gefen

3. Once the LED under Input 2 turns bright blue, a picture will be displayed on the display connected to Out 3 on the Matrix.Note that in Fig 1.1, Out

1 LED Button Press IndicatorThis LED will be activated momentarily each time a button is pressed.2 Display and Source Selection ButtonsThese buttons

9IR REMOTE DESCRIPTIONExample 1:Route the source connected to In 3 to the display connected to Out 4.1. Press button 15 (Input 3) on the IR remote co

10IR REMOTE INSTALLATIONInstalling the IR Remote Control Battery1.Remove the battery cover on the back of the IR Remote Control unit.2. Insert the inc

Resolving IR Code Confl ictsIn the event that IR commands from other remote controls confl ict with thesupplied IR remote control unit, changing the rem

CHANGING THE IR CHANNELSetting The IR Channel on the MatrixUse the following procedure to set the proper IR channel on the Matrix.1 Press and hold the

13Back of CabinetGefen Toolbox UnitRemoteSet-top BoxIR EXTENDER INSTALLATIONUsing The IR ExtenderAn optional IR Extender (Gefen Part No. EXT-RMT-EXTIR

Understanding EDIDThe GefenToolBox 4x4 Matrix with FST features automatic and manual EDID adjustments to maximize compatibility of all attached device

15EDID MANAGEMENTEDID Mode Selection• EXTERNAL MODE:To use this mode, set the EDID Mode Switch on the front panel to theEXTposition. In External EDID

16EDID MANAGEMENTAudio Channel SelectionThe GefenToolBox 4x4 Matrix with FST features a switch that will modify the supported audio formats listed in

ASKING FOR ASSISTANCERev A3Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM

17External EDID ManagementThe GefenToolBox 4x4 Matrix with FST features EDID Management. Before thesource can send video or audio signals to the disp

18EDID MANAGEMENTInternal EDID Specifi cationsThe table below lists the settings that comprise the built-in Internal EDID data structure:Video Data Blo

FAST SWITCHING TECHNOLOGY19Fast Switching TechnologyFast Switching Technology (FST) is a Gefen software implementation for HDMI 1.3 products. FST was

543219876123456789Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interfaceThis feature allows for easy integration into automa

WALL MOUNTING INSTRUCTIONSThe GefenToolBox 4x4 Matrix with FST should be mounted vertically in a wall or cabinet with wood/drywall screws as shown in

Maximum Pixel Clock ... 225 MHzMaximum Video Resolution ...

WARRANTY23Gefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects

Rev A3PbThis product uses UL listed power supplies.

CONTENTS1 Introduction2 Operation Notes3 Features4 Panel Layout5 Panel Descriptions6 Connecting And Operating The GefenToolBox 4x4 Matrix with FST8 I

Congratulations on your purchase of the GefenToolBox 4x4 Matrix with FST. Your complete satisfaction is very important to us.About GefenWe specialize

READ THESE NOTES BEFORE INSTALLING OROPERATING THE GEFENTOOLBOX 4X4 MATRIX WITH FST• EDID contains the A/V capabilities of a display device in regards

FEATURES3Supported HDMI 1.3 Features• 225 MHz (up to 12 bit YUV 444 @ 1080p)• Deep Color• Dolby TrueHD and DTS-HD Master Audio • Lip-SyncGeneral Featu

PANEL LAYOUT106421219743Side Panel11Front Panel58

PANEL DESCRIPTIONS1 HDMI Input Ports 1-4Connect HDMI source devices to these ports.2 Fast / Slow SwitchSwitches between Fast and Slow Switching. Se

6How to Connect the GefenToolBox 4x4 Matrix with FST1.Use one of the provided HDMI cables to connect the source device to theHDMI input port of the Ge