Gefen GEF-3GSDI-16416-PB Spezifikationen

1080P

7BACK PANEL DESCRIPTIONSBack Panel1Reference In ConnectorConnect an external reference to this connector. Bi-level (black burst) and tri-level sync a

83G-SDI DisplaysSDI CABLE 16x3G-SDI Sources16xMatrixRS-232 ControllerRS-232 CABLEETHERNET CABLEComputer(IP Control)CONNECTING THE16X16 3GSDI PUSH BUTT

9OPERATING THE16X16 3GSDI PUSH BUTTON MATRIXThe Standby ScreenThe front panel of the 16x16 3GSDI Push Button Matrix has a 16 character 2 lineLCD displ

10OPERATING THE16X16 3GSDI PUSH BUTTON MATRIXDisplaying the Current Routing State1. To display the current routing status of the Matrix, press any one

11MODE BUTTONSRouting Sources1To change the current routing state, press Set Button to activate RoutingMode.2 Press the desired Output button. One or

12MODE BUTTONSSystem Lock ModeLocking the Matrix prevents changes to any of the Matrix settings. This feature is useful in case any of the front pane

13MODE BUTTONSCycling between Information ScreensPress the Cancel button, while in Status Check Mode, to cycle through the Information Screens.CancelC

14MODE BUTTONSSaving the current Routing State1Set the routing state (see page 11), then press the PreSet button twice to activate Preset Mode.2 Press

15MODE BUTTONSRecalling a stored Routing State1Press the PreSet button onceto activate Recall Preset Mode.2 Press the Input button (1 - 16) of the rou

16MODE BUTTONSMasking OutputsMasking prevents the output device (display, etc) from receiving an output signal, instead of powering-down the output de

ASKING FOR ASSISTANCETechnical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM Monda

17MODE BUTTONSCommunication ModesThe Comm button allows the Matrix to switch between RS-232 and RS-485 (EIA-485) modes.1 Press the Comm button to acti

18IR REMOTE CONTROL DESCRIPTIONSRMT-16416IRRemote Control Unit1Activity IndicatorThis LED will be glow yellow each time a button is pressed.2 Display

19Installing the RMT-16416IR Battery1.Remove the battery cover on the back of the IR Remote Control unit.2. Insert the included battery into the open

20IR REMOTE CONTROL CONFIGURATIONHow to Resolve IR Code Confl ictsIn the event that IR commands from other remote controls interfere with the supplied

21USING THE IR REMOTE CONTROLIR Remote Control Key MappingEach input and output on the 16x16 3GSDI Push Button Matrix is represented by abutton on the

22What features are available via the RS-232 serial communications port?pThe 16x16 3GSDI Push Button Matrix can accept commands through the RS-232 ser

23RS-232 SERIAL CONTROLRS-232 FeaturesRS-232 remote commands are used to control this product’s features. Features include input / output routing and

24RS-232 SERIAL CONTROL#PRREFTABLE CommandThe #PRREFTABLE command displays the Ref In data table (timings) which arerecognized by the 16x16 3GSDI Push

25RS-232 SERIAL CONTROL#RSTIP CommandThe #RSTIP command sets the current IP confi guration to factory (default)settings.Syntaxy:#RSTIPParameters:NoneNo

26RS-232 SERIAL CONTROL#SNETMASK CommandThe #SNETMASK command specifi es a new net mask.Syntaxy:#SNETMASK param1 param2 param3 param4Parameters:param1

CONTENTS1 Introduction2 Operation Notes3 Features4 Front Panel Layout5 Front Panel Descriptions6 Back Panel Layout7 Back Panel Descriptions8 Conne

27RS-232 SERIAL CONTROL#SPORT CommandSpecifi es a new port.Syntaxy:#SPORT param1Parameters:param1 Port [0 - 255]Notes:A reboot is required after u

28RS-232 SERIAL CONTROL#FADEFAULT CommandThe #FADEFAULT command sets all routing states to default (1 - 1, 2 - 2, 3 - 3, etc).Syntaxy:#FADEFAULTParame

29R CommandThe R command allows specifi c routing of inputs and outputs.Syntaxy:r param1 param2Parameters:param1 3GSDI Ouput [1 - 16]param2 3GSDI

30IP CONTROLThe GefenPRO 16x16 3GSDI Push Button Matrix supports IP-based controlusing an integrated Web interface. To access this feature, an IP addr

31IP CONTROLMaskingTheMaskingpage is used to hide an output from displaying any video. From this page, all outputs can be set to “Active” or “Mask”. W

32IP CONTROLIP Confi gurationThe IP Confi guration page is used to set the IP settings that will be used toaccess the Web interface. The following items

33IP CONTROLBackup / RestoreTheBackup/Restore page is used to backup and restore setup confi gurations.Note: This feature will be implemented in a fut

34FIRMWARE UPDATEFirmware UpdateFollow the on-screen instructions to complete the fi rmware update process:1. Using Hyperterminal, enter the #ACTIVEBOL

35WARNING MESSAGESSystem FailureIn the case of a critical malcommand, the following warning message will be displayed on the Main Display:If the16x16

36RACK MOUNT SAFETY INFORMATIONa. Maximum recommended ambient temperature: 45 ˚C (104 ˚F).b. Increase the air fl ow as needed to maintain the recommend

1Congratulations on your purchase of the 16x16 3GSDI Push Button Matrix. Your complete satisfaction is very important to us.GefenGefen delivers innova

37SPECIFICATIONSInput / Output•SDI (SMPTE 259MI up to 360 Mbps)• HD-SDI (SMPTE 292M up to 1.485 Gbps)• 3G-SDI (SMPTE 424M/425M up to 3.0 Gbps)Supporte

38WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects

39LICENSINGlwIP is licenced under the BSD licence:Copyright (c) 2001-2004 Swedish Institute of Computer Science.All rights reserved.Redistribution and

Rev A1Pb

2READ THESE NOTES BEFORE INSTALLING OROPERATING THE 16X16 3GSDI PUSH BUTTON MATRIX• There is no internal scaling in the 16x16 3GSDI Push Button Matri

3Features•Supports resolutions up to 1080p, 1920x1200, and 2K.• Front panel control buttons for local switching.• Serial interface for remote control

4Front PanelFRONT PANEL LAYOUT563214

5FRONT PANEL DESCRIPTIONSFront Panel1 Mode ButtonsThese buttons are used to control other features on the product. See pages 11 -17 for more informat

6BACK PANEL LAYOUTBack Panel458976132