Gefen EXT-HDMI-CAT5-844 Bedienungsanleitung

www.gefen.comwww.gefen.com8x4 CAT-5 Matrix for EXT-HDMI-CAT5-844User Manual

7How to Connect the 8x4 CAT-5 Matrix for HDMI1. Connect up to 8 HDMI source devices to the 8x4 CAT-5 Matrix for HDMI using the included HDMI cables.N

8CONNECTING THE 8X4 CAT-5 MATRIX FOR HDMI JUMPERSThe 8x4 CAT-5 Matrix for HDMI uses a jumper cable system to link the matrix and extension portions to

9RMT-16IR* REMOTE CONTROL DESCRIPTIONThe RMT-16IR remote control will allow the user to select which source will be routed to which output. Each of th

10RMT-16IR REMOTE CHANNEL CONFIGURATIONWhy would I need to change the remote channel?In some instances, the 8x4 CAT-5 Matrix for HDMI may use IR codes

11EDID MANAGEMENT FEATUREEDID. What is it and what is it used for?Under normal circumstances, a source device (digital and analog) will require inform

12EDID MANAGEMENT OPTIONSEDID ModesThe diagram below illustrates the 8 DIP switch bank.DIP SWITCH Function1 EDID Mode2 EDID Mode3 IR Channel4 IR Chann

13LED ARRAY DESCRIPTIONThe LED array on the 8x4 CAT-5 Matrix for HDMI is designed to inform the user of the current source to output routes. Each outp

148X4 CAT-5 MATRIX FOR HDMI RS-232 SERIAL COMMUNICATIONWhat features are available via the RS-232 serial communications port?The 8x4 CAT-5 Matrix for

158X4 CAT-5 MATRIX FOR HDMI RS-232 COMMANDSSwitching/Routing Binary TableASCIICommandInput OutputASCIICommandInput OutputA1 or a1 1A 1 C1 or c1 1A 3A2

16Front PanelBack PanelTop Panel61031578924RECEIVER PANEL LAYOUT

Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM Monday thru Friday.Write T

171 IR Relay ReceiverThis receiver will receive commands from the included IR remote control and from other commercial IR remote controls and relay i

18OPERATING THE HDMI OVER CAT-5 RECEIVERTo use the HDMI Over CAT5 Receiver, the following connections must be made:1. A HDMI jumper cable is connect

19RMT-4IR REMOTE CONTROL DESCRIPTIONPressing on each numbered selection buttons will switch the receiver to the corresponding HDMI Input source. Each

20HDMI OVER CAT-5 RECEIVER ADVANCED CONFIGURATIONThe HDMI Over CAT5 Receiver contains a bank of 8 DIP SWITCHES. These swiches are located underneath e

21HDMI OVER CAT-5 RECEIVER ADVANCED CONFIGURATION1. Insert a small fl at head tool into the trim pot on the receiver unit.2. Turn the trim pot in a c

22LED ARRAY DESCRIPTIONThe LED array on the HDMI Over CAT5 Receiver is designed to inform the user of the currently selected source. Each receiver uni

23HDMI OVER CAT-5 RECEIVER RS-232 SERIAL COMMUNICATIONSWhat features are available via the RS-232 serial communications port?The HDMI Over CAT5 Receiv

24HDMI OVER CAT-5 RECEIVER RS-232 COMMANDSSwitching/Routing Binary TableASCIICommandInput11A21B32A42B53A63B74A84BBoost SettingsDIP switches 4 and 5 on

25Video Amplifi er Bandwidth ... 165 MHzInput Video Signal ...

CONTENTS1 Introduction2 Operation Notes3 Features4 Sender Panel Layout5 Sender Panel Descriptions7 Connecting And Operating The 8x4 CAT-5 Matrix fo

1Congratulations on your purchase of the 8x4 CAT-5 Matrix for HDMI. Your complete satisfaction is very important to us.GefenGefen delivers innovative,

READ THESE NOTES BEFORE INSTALLING OROPERATING THE 8X4 CAT-5 MATRIX FOR HDMI• To use the extender functionality of the 8x4 CAT-5 Matrix for HDMI the

3Features• Switches any eight HDMI™ sources to 4 Displays• Distributes any of the four switched inputs (total of eight inputs) to any combination of

4Front PanelBack Panel11011 1223 4135 8679SENDER PANEL LAYOUT

51 HDMI Outputs 1 - 4The selected source for each HDMI output will be indicated by an active LED. The LED array will behave differently depending on

6SENDER PANEL DESCRIPTIONS12 HDMI Outputs 1 - 4Each output port can be used in one of either two ways. This output can be connected directly to a loc