Gefen GEF-DVI-848DL-PB Bedienungsanleitung

8x8 DVIDual Link Matrixw/ Push Button ControlsGEF-DVI-848DL-PBUser Manualwww.gefenpro.com

6PANEL LAYOUTBack Panel78136542

7PANEL DESCRIPTIONSBack Panel1 110 / 220 V AC (50 / 60 Hz) Power ReceptacleConnect the included AC power cord from this receptacle to an availableele

8CONNECTING AND OPERATING THE8X8 DVI DUAL LINK MATRIX WITH PUSH BUTTON CONTROLSHow to Connect the 8x8 DVI Dual Link Matrix with Push Button Controls1.

9FRONT PANEL DISPLAYMain DisplayThe Main Display of the GefenPRO 8x8 DVI Dual Link Matrix is a 16-character two-line display. This display will show t

RMT-8IRRemote Control Unit1 Activity IndicatorThis LED will be activated momentarily each time a button is pressed.2 Source / Monitor Selection Button

11IR REMOTE INSTALLATIONInstalling the Battery1. Remove the battery cover on the back of the IR Remote Control unit.2. Insert the included battery in

12IR REMOTE CONFIGURATIONHow to Resolve IR Code Confl ictsIn the event that IR commands from other remote controls interfere with the supplied IR Remot

13USING THE IR REMOTE CONTROL UNITIR Remote Control Key MappingEach input and output on the 8x8 DVI Dual Link Matrix with Push Button Controls is repr

14OPERATING THE 8X8 DVI DUAL LINK MATRIXRouting SourcesIn order to change current routing state:1 Press Set Button to activate Routing Mode.2 Press an

15OPERATING THE 8X8 DVI DUAL LINK MATRIXSystem Lock ModeLocking the Matrix prevents changes to any of the Matrix settings. This feature is useful in

16OPERATING THE 8X8 DVI DUAL LINK MATRIXCycling between Information ScreensPress the Cancel button, while in Status Check Mode, to cycle through the I

17OPERATING THE 8X8 DVI DUAL LINK MATRIXActivating / Deactivating Standby Mode:Press and hold the Cancel button for 5 seconds to activate or deactivat

18OPERATING THE DVI 8X8 DUAL LINK MATRIX2 Press the Output button to select the EDID data source.3Press the Input button to select EDID data destinati

19OPERATING THE DVI 8X8 DUAL LINK MATRIXSaving the default EDID to Local Memory1Press the EDID button twice to activate DETOLO (Default EDID To Local)

20OPERATING THE DVI 8X8 DUAL LINK MATRIXSaving the current Routing State1Set the routing state (see page 14), then press the PreSet buttontwice to act

21OPERATING THE DVI 8X8 DUAL LINK MATRIXRecalling a Routing State1 Press the PreSet button onceto activate Recall Preset Mode.2 Press the Input button

22OPERATING THE 8X8 DVI DUAL LINK MATRIXMasking OutputsMasking prevents the output device (display, etc) from receiving an output signal, instead of p

23RS-232 SERIAL CONTROLRS232 SettingsBits per second ...

24IP CONFIGURATIONConfi guring the IP AddressThe8x8 DVI DL Matrix supports IP-based control using Telnet or the built-in xWeb-based GUI. To set up IP

25RS-232 / TELNET COMMANDSEDID ManagementCommandDescription#dynamic_edidEnables / disables dynamic EDID#edidbatoloRead downstream EDID and stores in a

ASKING FOR ASSISTANCERev A5Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM - 5:00 PM

26RS-232 / TELNET COMMANDS#edidbatolo CommandThe #edidbatolo command reads the downstream EDID and stores it to any local input. Up to eight inputs c

27RS-232 / TELNET COMMANDS#ediddetolo FunctionThe #ediddetolo function stores the Default EDID (640x480) in the specifi edLocal EDID inputs. Up to eig

28RS-232 / TELNET COMMANDS#ediddstoba FunctionThe #ediddstoba function reads the downstream EDID and stores it to a specifi ed EDID bank.Syntaxy:#edidd

29RS-232 / TELNET COMMANDS#ediddstolo FunctionThe #ediddstolofunction reads the downstream EDID and stores it to a Local EDID input.Syntaxy:#ediddstol

30RS-232 / TELNET COMMANDS#lock_edid FunctionThe #lock_edid function secures the Local EDID and disables the automaticloading of the downstream EDID a

31RS-232 / TELNET COMMANDS#prbaedid FunctionThe #prbaedid function reads the EDID fi le from the specifi ed bank and sends to serial port.Syntaxy:#prbae

32RS-232 / TELNET COMMANDS#prdsedid FunctionThe #prdsedid function reads the downstream EDID and sends it to the serial port.Syntaxy:#prdsedid param1P

33RS-232 / TELNET COMMANDS#predidst FunctionThe #predidst function reads the downstream EDID. This function displays atable containing details relati

34RS-232 / TELNET COMMANDS#prloedid FunctionThe #prloedid function reads the local EDID of a specifi ed input and spools it to the serial port.Syntaxy:

35RS-232 / TELNET COMMANDSIP / Telnet Confi gurationCommandDescription#display_telnet_welcomeSet Telnet welcome message on login#ipconfi g Displays all

CONTENTS1 Introduction2 Operation Notes3 Features4 Front Panel Layout5 Front Panel Descriptions6 Back Panel Layout7 Back Panel Descriptions8 Conne

36RS-232 / TELNET COMMANDS#ipconfi g CommandThe #ipconfi g command displays the current TCP/IP settings for the matrix.Syntaxy:#ipconfi gParameters:NoneE

37RS-232 / TELNET COMMANDS#resetip CommandThe #resetip command resets all TCP/IP settings to factory defaults.Syntaxy:#resetipParameters:None Notes:T

38RS-232 / TELNET COMMANDS#set_telnet_pass CommandThe #set_telnet_pass command sets the Telnet password. The maximum lengthof the password is 20 char

39RS-232 / TELNET COMMANDS#set_telnet_username CommandThe #set_telnet_username command sets the Telnet user name. The maximum length of the user name

40RS-232 / TELNET COMMANDS#show_telnet_pass CommandThe #show_telnet_pass command shows the Telnet password for login(if required).Syntaxy:#show_telnet

41RS-232 / TELNET COMMANDS#show_ver_data CommandThe #show_ver_data command displays the hardware and fi rmware version of the matrix.Syntaxy:#show_ver_

42RS-232 / TELNET COMMANDS#snetmask CommandThe #snetmask command sets the IP network mask. Dot-decimal notation must be used when specifying the IP n

43RS-232 / TELNET COMMANDSRoutingCommandDescription#callpresetRecalls a routing / mask preset#prpresetPrints the routing preset table#savepresetSaves

44RS-232 / TELNET COMMANDS#prpreset CommandThe #prpreset command displays the routing preset table.Syntaxy:#prpresetParameters:NoneExamplep:#prpresetP

45RS-232 / TELNET COMMANDS#savepreset CommandThe #savepreset command saves the current routing state to the specifi edpreset. Any masked outputs will

1INTRODUCTIONCongratulations on your purchase of the GefenPRO 8x8 DVI Dual Link Matrix with Push Button Controls with Push Button Controls. Your compl

46RS-232 / TELNET COMMANDSr CommandThe r commandroutes the specifi ed input to the specifi ed outputs. Syntaxy:r param1 param2 [param3...param9]Paramete

47RS-232 / TELNET COMMANDSs CommandThe s command routes the specifi ed input to all outputs.Syntaxy:s param1Parameters:param1 Input [1 - 8]Example

48RS-232 / TELNET COMMANDSMaskingCommandDescription#maskoutMasks the selected (video) output(s)#unmaskoutUnmasks the selected output(s)#maskout Comman

49RS-232 / TELNET COMMANDS#unmaskout CommandThe #unmaskout command unmasks the specifi ed outputs. If param1 = 0, then all outputs will be unmasked.Sy

50RS-232 / TELNET COMMANDSMiscellaneousCommandDescription#activeboloActivates the boot loader#fadefaultResets the matrix to factory default routing#he

51RS-232 / TELNET COMMANDS#fadefault CommandThe #fadefault command disables the EDID lock state, sets the default routingstate (1-1, 2-2, 3-3, etc.) a

52RS-232 / TELNET COMMANDS#help CommandThe #help command displays help on the specifi ed command. If param1 is not specifi ed, then the full list of co

53RS-232 / TELNET COMMANDS#set_input_name CommandThe #set_input_name command provides a name to the selected input.For example, “Input 1” could be ren

54RS-232 / TELNET COMMANDS#set_output_name CommandThe #set_output_name command provides a name to the selected output. For example, “Output 1” could

55RS-232 / TELNET COMMANDS#show_voltageThe #show_voltage command provides voltage information for the matrix.Syntaxy:#show_voltageParameters:NoneExamp

OPERATION NOTES2READ THESE NOTES BEFORE INSTALLING OROPERATING THE GEFENPRO 8X8 DVI DUAL LINK MATRIX WITH PUSH BUTTON CONTROLS• The 8x8 DVI Dual Link

56RS-232 / TELNET COMMANDSf CommandEnables / disables 5V on pin 14 of the specifi ed DVI input. This command isused when connecting the Receiver modul

57RS-232 / TELNET COMMANDSl CommandThe l (lower-case “L”) command displays the link status of each input. If the input is receiving a dual-link signa

58RS-232 / TELNET COMMANDSm CommandThe m command displays the current matrix status and routing information.Syntaxy:mParameters:NoneExamplep:m Output

59WEB INTERFACEView Matrix StatusMatrix StatusDisplays the current routing status of each input and output on the matrix.RefreshClick to refresh the M

60WEB INTERFACESwitch OutputsUsed to route the specifi ed input to the selected output(s). To route a source,place a check mark next to each Output.

61WEB INTERFACERecall PresetClick the down-arrow on the pull-down list to select the routing state (1-8) to recall. Click the Recall Preset button to

62WEB INTERFACESave Output NameSelect the DVI output to rename from the pull-down list. Type the name of the output in the Output Name fi eld. Click

63WEB INTERFACEManage EDIDSet Input to Default EDIDEDID StatusDisplays the current EDID status for each input on the matrix andindicates the current L

64WEB INTERFACESet Default EDIDPlace a check mark next to the input(s) that should be set to the default EDID.Click the Set Default EDID button to app

65WEB INTERFACEUpload EDIDLoad EDID fi lePlace a check mark next to the input(s) that will receive the EDID data from thefi le. The EDID fi le must be i

3FEATURESFeatures• Increases productivity•Supports resolutions up to 1920x1200 (Single Link) and 3840x2400 (Dual Link)• Front panel control buttons f

66WEB INTERFACEDownload EDIDDownload EDID File to PCSelect the radio button next to the output, containing the EDID to be downloaded. Click the Downl

67WEB INTERFACECopy EDIDSelect Source to Copy from / Select Input(s) to Copy toClick the radio button next to the input or output containing the EDID

68WEB INTERFACEEDID Lock StateUpdate EDID Lock StateSecures the Local EDID and disables the automatic loadingof the downstream EDID after the Matrix i

69WEB INTERFACEMaskingMatrix Mask Status / ChangeDisplays the current masking status for each output.MaskClick the Mask button to mask the selected ou

70WEB INTERFACEIP Confi gurationIP SettingsAssigns IP address, subnet, gateway, HTTP listening port, and Telnet port.Note that the MAC address can not

71WEB INTERFACEBackup / RestoreThe Backup / Restore feature for the 8x8 DVIKVM Dual Link Matrix is not currently implemented and will be available in

72WEB INTERFACEPower ManagementPower StatusEnabling this feature will store the +5V status for that input prior to shutting down the matrix. This pre

73WEB INTERFACEPower Lock StateIn the case of an accidental power loss to the matrix, the +5V state for eachinput can be preserved.Set the specifi ed P

74NETWORK CABLE WIRING DIAGRAMGefen recommends the TIA/EIA-568-B wiring option. Please adhere to the table below when fi eld-terminating the cable for

75FIRMWARE UPDATEFirmware Update ProcedureThe following items are required to update fi rmware:• RS-232 Terminal (e.g. Windows-based PC running HyperTe

4PANEL LAYOUTFront Panel45617283910 1112

76FIRMWARE UPDATE8. A message will appear in the terminal program:Waiting for the fi le to be sent ... (press ‘a’ to abort)9. In Hyperterminal, click T

77RACK MOUNT SAFETY INFORMATIONa. Maximum recommended ambient temperature: 45 ˚C (104 ˚F).b. Increase the air fl ow as needed to maintain the recommend

78SPECIFICATIONSMaximum Pixel Clock...2 x 165 MHzInput Video Signal...

79WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects

80LICENSINGlwIP is licenced under the BSD licence:Copyright (c) 2001-2004 Swedish Institute of Computer Science.All rights reserved.Redistribution and

Rev A520600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefenpro.com [email protected]

5PANEL DESCRIPTIONSFront Panel1 CancelThis button is used to cancel a routing change in progress.2 EDIDThis button is used to manage EDID functions.