Gefen GEF-HDFST-848-4ELR Bedienungsanleitung

8x8 Matrix for HDMIw/4 ELR-POL OutputsGEF-HDFST-848-4ELRUser Manual1080P®www.gefenpro.com

6MATRIX DESCRIPTIONSFront1LCD DisplayThis is a two-line, sixteen-character display that shows status information and isalso used to manage display / s

7MATRIX DESCRIPTIONSBack9 IP ControlConnect an Ethernet cable to this port to control the 8x8 Matrix for HDMI w/4ELR-POL Outputs using IP Control. Se

ELR-POL RECEIVER LAYOUT8TopFrontBack2143

ELR-POL RECEIVER DESCRIPTIONS9Top / Front / Back1Power IndicatorThis LED indicator will glow bright blue when the matrix is powered and the ELR-POL Re

1 LED Button Press IndicatorThis LED will be activated momentarily each time a button is pressed.2 Display and Source Selection ButtonsThese buttons

11IR REMOTE CONTROLInstalling the BatteryThe Remote Control unit ships with two batteries (CR2032 lithium battery).One battery is required for operati

12How to Connect the 8x8 Matrix for HDMI w/4 ELR-POL Outputs1.Connect up to eight Hi-Def sources to the8x8 Matrix for HDMI w/4 ELR-POL Outputs using H

OPERATING THE 8X8 MATRIX FOR HDMIMain DisplayTheMain Display of the 8x8 Matrix for HDMI w/4 ELR-POL Outputsis a 16scharacter 2 line display. This disp

Determining the Current Routing StateIn the example below, the fi rst row (OUT) represents each HDMI output onthe matrix. The bottom row (IN) represen

Routing SourcesSelecting the Output1. To select the output, press the Out - or Out + button once. The routing state for Output A will be displayed:2

3. Consecutively pressing the Out - button will cycle through each output,from right to left.Changing the Source4. Once the desired output has been se

5. Consecutively pressing the Input - button will decrease the input value by a factor of 1 (within a range of 1 - 8). For example, if Input 3 was or

18OPERATING THE 8X8 MATRIX FOR HDMILocking / Unlocking the Front PanelTo prevent an accidental routing change or power-down (by pressing thePowerbutt

19OPERATING THE 8X8 MATRIX FOR HDMIFast Switching TechnologyFast Switching Technology (FST) is a Gefen software implementation for HDMIproducts. FST

OPERATING THE 8X8 MATRIX FOR HDMI20Determining the Current Switching ModeEach HDMI input can be set to Fast Mode or Slow Mode. It is recommended that

OPERATING THE 8X8 MATRIX FOR HDMI3. Press the Output - or Output + button again to cycle through the routing state for each output. Consecutively pr

Changing the Switching Mode5. Once the desired input has been selected, press the Input + or Input -button to toggle between Fast or Slow switching mo

OPERATING THE 8X8 MATRIX FOR HDMISetting the IR Channel on the 8x8 Matrix for HDMIIn order for the 8x8 Matrix for HDMIto communicate with the included

3. After setting the IR address, make sure that the DIP switches on the IR Remote Control are set according to the information in the LCD display.See

OPERATING THE 8X8 MATRIX FOR HDMI25Routing Sources using the IR Remote ControlButtons1 - 8 on the IR remote control correspond to each HDMI input (Inp

ASKING FOR ASSISTANCERev A1Technical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM

OPERATING THE 8X8 MATRIX FOR HDMI263. After the input and output have been selected on the IR Remote Control, thenumbers on the far right-hand of the

EDID MANAGEMENT27External EDID ManagementThe8x8 Matrix for HDMI features EDID Management. Before the source canIsend video or audio signals, the sour

28RS-232 SERIAL CONTROLRS232 SettingsBits per second ...

29IP CONFIGURATIONConfi guring the IP AddressThe8x8 Crosspoint Matrix for HDMI supports IP-based control using Telnet.ITo set up Telnet control, the ne

RS-232 / TELNET COMMANDS30IP / Telnet Confi gurationCommandDescription#display_telnet_welcomeSet Telnet welcome message on login#ipconfi g Displays all

RS-232 / TELNET COMMANDS31#display_telnet_welcome CommandThe #display_telnet_welcome command sets (enables/disables) the Telnetwelcome message on logi

RS-232 / TELNET COMMANDS32#ipconfi g CommandThe #ipconfi g command displays the current TCP/IP settings for the matrix.Syntaxy:#ipconfi gParameters:NoneE

RS-232 / TELNET COMMANDS33#resetip CommandThe #resetip command resets all TCP/IP settings to factory defaults.Syntaxy:#resetipParameters:None Notes

RS-232 / TELNET COMMANDS34#set_http_port CommandThe #set_http_port command sets the Web server listening port. The underscorecharacters (“_”) must be

RS-232 / TELNET COMMANDS35#set_mac_addr CommandThe #set_mac_addr command set the MAC address of the Matrix.The underscore characters (“_”) must be inc

CONTENTS1 Introduction2 Operation Notes3 Features4 Matrix Layout4 Front5 Back6 Matrix Descriptions6 Front7 Back8 ELR-POL Receiver Layout9 ELR-

RS-232 / TELNET COMMANDS36#set_telnet_pass CommandThe #set_telnet_pass command sets the Telnet password. The underscorecharacters (“_”) must be inclu

RS-232 / TELNET COMMANDS37#set_telnet_port CommandThe #set_telnet_port command sets the Telnet listening port. The underscore characters (“_”) must b

38RS-232 / TELNET COMMANDS#set_telnet_username CommandThe #set_telnet_username command sets the Telnet user name.The underscore characters (“_”) must

39RS-232 / TELNET COMMANDS#set_webui_pass CommandThe #set_webui_pass command sets the password for the Web interface.The underscore characters (“_”) m

40RS-232 / TELNET COMMANDS#set_webui_username CommandThe #set_webui_username command sets the user name for the Web interface. The underscore characte

41RS-232 / TELNET COMMANDS#sgateway CommandThe #sgateway sets the IP gateway (router) address. Dot-decimal notation must be used when specifying the

42RS-232 / TELNET COMMANDS#show_gateway CommandThe #show_gateway command shows the current gateway address.The underscore characters (“_”) must be inc

43RS-232 / TELNET COMMANDS#show_ip CommandThe #show_ip command shows the current IP address of the Matrix.The underscore character (“_”) must be inclu

44RS-232 / TELNET COMMANDS#show_netmask CommandThe #show_netmask shows the netmask address. The underscore character (“_”) must be included when typi

45RS-232 / TELNET COMMANDS#show_telnet_username CommandThe #show_telnet_username command returns the user name required for login. The underscore cha

Congratulations on your purchase of the GefenPRO8x8 Matrix for HDMI w/4ELR Outputs. Your complete satisfaction is very important to us.About GefenWe s

46RS-232 / TELNET COMMANDS#show_webui_username CommandThe #show_webui_username command returns the user name required for login. The underscore chara

47RS-232 / TELNET COMMANDS#sipadd CommandThe #sipadd command sets the IP address of the matrix. Dot-decimal notationmust be used when specifying the

48RS-232 / TELNET COMMANDS#snetmask CommandThe #snetmask command sets the IP network subnet mask. Dot-decimalnotation must be used when specifying th

49RS-232 / TELNET COMMANDS#use_telnet_pass CommandThe #use_telnet_pass command requires or disables Telnet login credentials. The default setting is d

50RS-232 / TELNET COMMANDS#use_webui_pass CommandThe #use_webui_pass command requires or disables Web UI login credentials. The default setting is di

RS-232 / TELNET COMMANDS51Routing / Naming / PresetsCommandDescription#lock_matrix Locks / unlocks the Matrix#recall_presetRecalls a routing / mask pr

RS-232 / TELNET COMMANDS52#lock_matrix CommandThe #lock_matrix command locks / unlocks the Matrix. When the Matrix islocked, all functions are disabl

RS-232 / TELNET COMMANDS53#recall_preset CommandThe #recall_preset command recalls a routing preset. Any masked outputs will also be recalled. The u

RS-232 / TELNET COMMANDS54#set_input_name CommandThe #set_input_name command provides a name to the selected input.For example, “Input 1” could be ren

RS-232 / TELNET COMMANDS55#set_output_name CommandThe #set_output_name command provides a name to the selected output. For example, “Output 1” could

READ THESE NOTES BEFORE INSTALLING OROPERATING THE 8X8 MATRIX FOR HDMI W/4 ELR-POL OUTPUTS• EDID contains the A/V capabilities of a display device in

RS-232 / TELNET COMMANDS56#show_input_name CommandThe #show_input_name command shows the name provided to the specifi ed input using the #set_input_nam

RS-232 / TELNET COMMANDS57#show_r CommandThe #show_r command shows the current routing status of the specifi ed output. The underscore character (“_”)

RS-232 / TELNET COMMANDS58r CommandThe r commandroutes the specifi ed input to the specifi ed outputs. If param2is2set to 0, then the specifi ed input i

RS-232 / TELNET COMMANDS59s CommandThe s command routes the specifi ed input to all outputs. Unlike othercommands, do not precede the r command with th

RS-232 / TELNET COMMANDS60StatusCommandDescription#help Displays all available commands#show_fw Displays the Matrix fi rmware version#show_hpdDisplays

RS-232 / TELNET COMMANDS61#show_fw CommandThe #show_fw command displays the current fi rmware version of the Matrix. The underscore character (“_”) mu

RS-232 / TELNET COMMANDS62#show_hdp CommandThe #show_hpd command displays the HPD (Hot-Plug Detect) status of thespecifi ed output. The underscore cha

RS-232 / TELNET COMMANDS63#show_rsense CommandThe #show_rsense command displays Rsense status of the specifi ed output. The underscore character (“_”)

RS-232 / TELNET COMMANDS64m CommandThe m command displays the current matrix routing status in table format.Unlike other commands, do not precede the

RS-232 / TELNET COMMANDS65n CommandThe n command displays the current input-output routing state for the specifi ed output. Unlike other commands, do

FEATURES3Supported HDMI Features•Resolutions up to 1080p Full HD• HDCP compliant• 12-bit Deep Color• x.v. Color• LPCM 7.1 audio, Dolby Digital® Plus,

66RS-232 / TELNET COMMANDSMaskingCommandDescription#activeisp Activates ISP mode for fi rmware updates#echoEnables / disables RS-232 feedback#fadefault

67RS-232 / TELNET COMMANDS#echo CommandThe #echo command enables / disables serial port (terminal) echo.Syntaxy:#echo Parameters:param1 Value [

RS-232 / TELNET COMMANDS68#fadefault CommandThe #fadefault command disables the EDID lock state, sets the default routingstate (1-1, 2-2, 3-3, etc.),

RS-232 / TELNET COMMANDS69#mask CommandThe #mask command masks the specifi ed outputs. If param1 is set to 0, then all outputs are masked.Syntaxy:#mas

70RS-232 / TELNET COMMANDS#power CommandThe #power command toggles the power state on the matrix.Syntaxy:#power param1Parameters:param1 State [0

71RS-232 / TELNET COMMANDS#reboot CommandThe #reboot command reboots the matrix.Syntaxy:#rebootParameters:NoneExamplep:#rebootMATRIX WILL REBOOT SHORT

RS-232 / TELNET COMMANDS72#set_ir CommandThe #set_ir set the IR channel for the matrix. The associated DIP switch settingsfor the IR remote control u

RS-232 / TELNET COMMANDS73#show_mask CommandThe #show_mask command shows the mask status for the specifi ed output.The underscore character (“_”) must

RS-232 / TELNET COMMANDS74#show_out_colordpt CommandThe #show_out_colordpt command displays the highest color depth supported by the specifi ed display

RS-232 / TELNET COMMANDS75#show_out_res CommandThe #show_out_res command displays the highest resolution supported by thespecifi ed display based on th

MATRIX LAYOUT4Front24135 768

RS-232 / TELNET COMMANDS76#unmask CommandThe #unmask command unmasks the specifi ed outputs. Ifparam1 is set to 0,then all outputs are unmasked.Syntaxy

FIRMWARE UPDATE77Firmware Update ProcedureThe following items are required to update the matrix fi rmware:•GefenPRO8x8 Matrix for HDMI w/4 ELR-POL Outp

RACK MOUNT SAFETY INFORMATION78a. Maximum recommended ambient temperature: 40 ˚C (104 ˚F).b. Increase the air fl ow as needed to maintain the recommend

Maximum Pixel Clock...225 MHzVideo Input Connectors (Matrix)...

WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects an

Rev A1Pb20600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefenpro.com [email protected] product

MATRIX LAYOUT5Back91012 1513161814191711